| 品牌 | 其他 | 类型 | 储能用蓄电池 |
| 电池盖和排气拴结构 | 阀控式密闭蓄电池 | 化学类型 | 铅酸蓄电池 |
| 荷电状态 | 免维护蓄电池 | 电压 | 12（V） |
| 型号 | np | 额定容量 | 24 |
| 外型尺寸 | 165*125*175（mm） | 适用范围 | 太阳能蓄电池、UPS |
汇天成主要追求产品的先进性，可靠性和环保性，采用国际内化成高新技术及生产工艺，实现了企业的环保理念。外化成和内化成区别在于：传统蓄电池主要通过化成槽进行充电，化成后变为熟极板，然后出槽，负极板在接触空气和清洗时会快速氧化，很难保证电池极板质量，并产生废水，对环境造成很大污染；内化成则采用特殊配方的生极板，装入电池槽内密封充电，极板既不会接触到空气也不会氧化，正负极板充电均衡，电池一直性好，寿命长，真正实现了优化生产，绿色电池的环保理念。汇天成蓄电池使用无污染排放的工艺标准，减少蓄电池的极板污染，同时产品质量也大大提高。 HTCmainly pursuits the products’ advanced, reliability andenvironmental protection, it adopted the inner production process,the advanced high-tech in International field, to achieve the itsenvironmental philosophy. The difference between theinner-production and outer-production is: the traditional batterymainly be charged through the production slot, then they changedinto processed plate and get out of the slot. The negative platewould be rapid oxidized when exposed to air and cleaned.It isdifficult to ensure the of battery plates. And the producedwastewater would cause great pollution to the environment.
产品特点Features
免维护无须补液Maintenance free and without liquid added
适应温度广（-15-45℃） wide range of adaptation temperature(-15-45℃)
设计寿命长（5-8年） long design life (5-8 years)
安全防爆 safety explosion-proof
无游离电解液，侧倒90°仍能使用 no free electrolyte and can be still usefulwhen the side down of 90 °
内阻小，大电流放电性能好 Small internal resistance and good performance ofhigh current discharge
自放电小 Small self-discharge
荷电出厂，使用方便 charged before they leave the factory and easy touse
独特配方，深放电恢复性能好 Unique formula and good performance ofdeep-discharge recovery 注意attention
额定容量（1C10小时率）为在25℃下所得的平均值，可以通过10次以上的充、放循环使用； Nominal capacity(1C10-hour rate) is obtained at 25℃on average, can accept more than10 times of charge and discharge cycleuse 安装使用 Installation andUsage 使用前，请检查蓄电池外观（有无漏酸，破裂）。 Before use, check batteryskin (with seamless acid, rupture). 蓄电池的安装必须由专业人员来进行。 Thebattery must be installed byprofessionals. 在电池连接过程中，请戴好防护手套，使用扭矩扳手等金属工具时，请将金属工具进行绝缘包装以防触电。禁止将金属工具同时接触到电池的正、负端子，造成电池短路。 Inthe course of the battery connection, wear protective gloves. Whenuse a torque wrench and other metal tools, please insulationpackaging to prevent electric shock. Prohibit access metal tools tothe battery positive and negative terminals at same time. Otherwisecause the battery shortcircuit. 安装搬运电池时应均匀受力，受力处应为蓄电池壳的部分，避免损伤极柱。 The batteryshould be uniform force when Installation and carrying the battery.Force at the shell should be part of the battery shell to avoiddamage thepole. 禁止将不同品牌，不同容量的蓄电池并联或串联使用；电池在多只串联使用时，请按电池标识“+”，“-”极柱依次排列，电池之间的距离不能少于15mm,且连接部位要紧固，防止产生火花或接触不良。Prohibithybrid application of different brands and different capacitybatteries in parallel or in series. Please put the battery in orderof priority identified "+","-" pole when in a a multi-series usage.The space between batteries can not be less than 15mm and theconnection parts must be tightened to prevent sparks or instablecontact. 安装接插式端子的蓄电池时，请勿改变端子的形状和位置，如特殊情况需要，请与客户服务中心联系。 donot change the shape and location of terminals when Installingplug-in terminal of the battery. Please contact
customer service at special circumstancesrequire. 和外接设备连接之前，必须使设备处于断开状态，并再次检查蓄电池的连接极性是否正确，然后再将蓄电池（组）的正极连接设备的正极，蓄电池（组）的负极连接设备的负极端子，并紧固好连接线。 Thedevice must be disconnected and check again the correct of batterypolarity connection before connecting external devices. Thenconnect the positive cathode of the battery (group) to the positivecathode of devices, the negative anode to the negative cathodedevices terminal, and tighten the cable.
